Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
How to update the new zwave stick/driver?
#1
Happy Thankgiving.

Finally, have time to work on CQC again.

I cleaned up my zwave network via the RF Stick. I already have the New Zwave driver set up, but I still see the old items on it. How do I make sure that it updates?

Thank you
Reply
#2
Run the include process again. Z-Wave has no way to do that automatically. So you have to just put the master into include mode and tell the CQC driver to do an include. That will refresh it from the master and the new stuff should show up.

If you reset the master and added everything back in, then first do an EXCLUDE on our driver. Then go back and do an include so that it can get back in sync with the master AND get the correct new security info.
Dean Roddey
Explorans limites defectum
Reply
#3
I just tried three times but I am getting an error "replication failed". I have the two controllers about 6 inches away from each other.

Any suggestions?

Thank you
Reply
#4
Some more details. I just tried to reconfigure the driver (it may have had a communication error) but it says I dont have permission (same as my other issue). Note, I just ran an update before working on this today.

Thank you

01/01 00:00:00-CQC, CQCServer, CIDOrbSrvWorkThread_1
{
CQCKit, CQCKit_ThisFacility.cpp.4645, Failed/Authority, Error: 6108/0/0
User 'administrator' does not have sufficient rights to perform this operation
<CQCServer> CIDOrb_ThisFacility.cpp - 536
<CQCAdmin> CQCKit_CQCSrvAdminClientProxy.cpp - 1771
<CQCAdmin> CQCTreeBrws_DevicesBrws.cpp - 2450

}
Reply
#5
Almost anything gives me that error. Even trying to pause a driver
Reply
#6
I would assume that the 'administrator' account has not been given system admin rights. Unless you have renamed it, the default system admin account is Admin. If you created another one, you would have to have been logged in as Admin in order to create another system admin account, and you would have had to give it system admin rights. I'm assuming you didn't do that, and that 'adminstrator' is maybe set to power user or Normal level or something.

Check the account you are using and see what privilege level it is set to. If it's not a system admin, you won't be able to bump it because you aren't currently a system admin in that 'administrator' account. You'll likely have to log in under the original Admin account. And, in that case, you might as well then delete the administrator account and just use Admin.
Dean Roddey
Explorans limites defectum
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  ISYv2 Driver - FanLinc simplextech 4 169 02-04-2020, 06:55 PM
Last Post: simplextech
  SMS Driver / Sending MMS gReatAutomation 2 118 02-02-2020, 05:57 PM
Last Post: simplextech
  ISYv2 Driver - IOLinc Support simplextech 7 291 02-01-2020, 07:18 PM
Last Post: simplextech
  Z-Wave dual usb stick setup simplextech 7 255 01-20-2020, 01:32 PM
Last Post: simplextech
Big Grin ZWave & Switch Remotes / Dimmer Remotes gReatAutomation 6 321 01-16-2020, 07:05 AM
Last Post: gReatAutomation
  New V2 Nest driver Dean Roddey 92 15,509 01-06-2020, 05:09 PM
Last Post: keepersg
  [ZWAVE] Zooz ZSE40 v2 simplextech 2 137 01-05-2020, 12:02 PM
Last Post: simplextech
  Lutron RadioRA2 Driver and Lutron Visor Control gReatAutomation 28 2,106 12-10-2019, 03:45 PM
Last Post: Dean Roddey
  Question on CQC Driver Pack Install kblagron 1 179 11-26-2019, 06:38 PM
Last Post: Dean Roddey
  Please add Somfy ZRTSI to zwave models kfly 15 1,119 11-24-2019, 03:37 PM
Last Post: kfly

Forum Jump:


Users browsing this thread: 1 Guest(s)