Charmed Quark Systems, Ltd. - Support Forums and Community

Full Version: Official 5.3 Beta Discussion Thread
You're currently viewing a stripped down version of our content. View the full version with proper formatting.
Whoever sent me the Wayne Dalton dimmer (ids of 5/6/3) you'll have to tell me the actual model, since the info I found doesn't have the manufacturer ids listed so I can't cross reference it.
(04-11-2018, 05:01 PM)potts.mike Wrote: [ -> ]Dean,

I dont see the Aeotec Multisensor 6 (ZW100-A) in the devices. Also, noe of my ecolink motion sensors are reporting their battery level.

Can you send me that dump file again? I seem to have dislocated it. I probably deleted the wrong one as I was trying to clean up ones I'd done.
I've got the device info file for the ZW100-A basically done, I just need the dump file again. It implements security for some reason, so I need to know which classes are secured. The info provided never includes that though it's clearly extremely important. Personally I don't see much point in implementing security for this type of device anyway. It just adds overhead and uses extra battery power.
(04-12-2018, 10:25 AM)Dean Roddey Wrote: [ -> ]Whoever sent me the Wayne Dalton dimmer (ids of 5/6/3) you'll have to tell me the actual model, since the info I found doesn't have the manufacturer ids listed so I can't cross reference it.

HA-06WD
(04-12-2018, 10:32 AM)Dean Roddey Wrote: [ -> ]
(04-11-2018, 05:01 PM)potts.mike Wrote: [ -> ]Dean,

I dont see the Aeotec Multisensor 6 (ZW100-A) in the devices. Also, noe of my ecolink motion sensors are reporting their battery level.

Can you send me that dump file again? I seem to have dislocated it. I probably deleted the wrong one as I was trying to clean up ones I'd done.

Let me know if you need anything else.
(04-12-2018, 10:23 AM)Dean Roddey Wrote: [ -> ]That's the z-stick. Actually you don't even need to now. If you use the client side interface, the manual associations dialog will have a special entry in the list of units to add to the target which I think is [Driver], so you know that's the one.

Bizarrely, it's actually not easy to get the master controller's id. The only way I can see to get it is to watch from msgs from it during the replication process. Those have to come from it. But, otherwise, I can't see any way to get it.

Should I be indicating the End Point?
(04-12-2018, 07:26 AM)Dean Roddey Wrote: [ -> ]You may have to send me those again. I was getting a bunch of files and documents and such, and I may have gotten confused at some point there. It would probably be best to name the files after the make/model instead of the unit id. The id is in the file itself. Having a whole bunch of files named unitX makes it hard for me to keep up. I try to figure them out and rename them, but it's easy to get lost.

Maybe a good naming scheme would be:

yourname_make_model.txt

That would make it a lot easier to keep up with. Otherwise everyone has a unit3 or unit4 and keeping up which which one is whose is hard.

Zip file emailed.  I have so far not been able to get the Fibaro door/temp unit to scan properly, it must have very tight timing window, not sure how to time it right between CQC and waking the unit up.
Almost never. That would only be used if the target has multiple end points and you want the source unit to send notifications to one of them. The driver is a single end point so you'd never use it for associating with the driver.
(04-12-2018, 05:12 PM)potts.mike Wrote: [ -> ]
(04-12-2018, 10:32 AM)Dean Roddey Wrote: [ -> ]
(04-11-2018, 05:01 PM)potts.mike Wrote: [ -> ]Dean,

I dont see the Aeotec Multisensor 6 (ZW100-A) in the devices. Also, noe of my ecolink motion sensors are reporting their battery level.

Can you send me that dump file again? I seem to have dislocated it. I probably deleted the wrong one as I was trying to clean up ones I'd done.

Let me know if you need anything else.

OK, that indicates it doesn't implement security. The information on the Z-Wave alliance site is wrong at least as often as it is right. The info gotten from the unit itself is obviously the final word, and it says no security.
I vaguely remember being able to include it either way and not seeing the need for security.